Differences

This shows you the differences between two versions of the page.

--- blocks:player-setup:aes67 [2026-10-15 09:42] – [Getting Started] mattias
+++ blocks:player-setup:aes67 [2026-10-16 11:16] (current) – [System Requirements] mattias
@@ Line 1: / Line 1: @@
-=====PIXILAB Player AES67=====
+=====PIXILAB Player AES67 Audio over IP =====
 This article describes how to set up AES67 Audio over IP in PIXILAB Player.
-====System Requirements====
+==== System Requirements ====
-AES67 is available in PIXILAB Player starting from version 8.0.
+AES67 is available in PIXILAB Player from version 8.0.
-HW/NUC REQUIREMENTS TODO…
-NETWORK REQUIREMENTS TODO… PIXILAB Player AES67 is multicast only. This means that network switches must support IGMP etc. All network switches and cables must support gigabit speeds.
-PIXILAB Player can transmit 2-8 channels of 24 bit audio at 48 kHz with a packet time of 1 ms. Receivers must support this format. PIXILAB Player AES67 has been tested to work with AES67-compatible Dante devices. The PIXILAB Player AES67 streams are automatically discovered by Dante Controller (via the SAP/SDP protocol).
+**Player hardware**\\
+We recommend players with Intel processors, as these handle the real-time CPU task scheduling that AES67 depends on more reliably.
+**Network**
+  * All network switches and cables must support gigabit speeds.
+  * PIXILAB Player AES67 is multicast only, so switches must support IGMP snooping, and an IGMP querier must be present on the network.
+  * We recommend network hardware designed for A/V use. For example, Netgear's A/V range offers easy-to-use profiles for audio over IP.
+  * PIXILAB does not provide support or documentation for configuring networks for AES67/AoIP, as this is not specific to Blocks.
+**Audio format**\\
+PIXILAB Player transmits 2-8 channels of 24-bit audio at 48 kHz with a packet time of 1 ms. This format is fixed, so receivers must support it.
+**Compatibility**\\
+PIXILAB Player AES67 has been tested with AES67-compatible Dante devices such as Audinate Dante AUIO receivers and Genelec speakers. Any device with modern Audinate chipset should be able to receive AES67.  Streams are automatically discovered by Dante Controller software via autodiscovery (SAP/SDP). Ususally a Audinate controller can only do either AES67 or Dante, not both at the same time.
+**Clock synchronization**\\
+PIXILAB Player uses PTP (IEEE 1588) for clock synchronization. PTP is implemented in software, hence the player does not rely on hardware timestamping in the network adapter. In a  AoIP network, the leader clock is normally selected automatically by the devices. All other devices synchronize their clocks to the elected leader. The current leader and synchronization status can be inspected in Dante Controller.
 ====Getting Started====
 To enable AES67 in PIXILAB Player, the aes67_dest= configuration option must be set in the player configuration file. The aes67_dest= option must be set to a valid multicast address (e.g., 239.69.0.121) that is not in use by any other AES67 transmitter. The player configuration file can be edited from within the Display Spot settings as seen in the screenshot below:
@@ Line 20: / Line 32: @@
 {{:blocks:player-setup:aes:configav.jpg|?800|}}
-**IMPORTANT:** For performance reasons, it is NOT recommended to enable AES67 in the player configuration file while not using the “AES67 Audio over IP” sound output.
 After selecting the “AES67 Audio over IP” audio output, the AES67 stream from the player will appear in Dante Controller as shown below.
 {{:blocks:player-setup:aes:dantecontroller.jpg?750|}}
+**IMPORTANT:** For performance reasons, it is NOT recommended to enable AES67 in the player configuration file while not using the “AES67 Audio over IP” sound output.